The RTCU product line currently includes 13 different hardware variants covering a broad range of I/O configurations, environments and applications.
All RTCU products offers full programmability using the RTCU-IDE Development Environment, but can also be used, without programming or development, with the RTCU MICRO Standard Application.

All the different RTCU products are compared in the RTCU Product Comparison Feature Chart.

All Products are delivered according to the conditions in the User License Agreement and Limited Warranty document.

RTCU Units
	RTCU CX1 pro/pro-c The RTCU CX1 pro/pro-c is a compact, waterproof and ruggedized telematic tracking and control platform, based on the powerful X32-architecture also found in the popular MX2i Series. In addition to a long list of standard features, the RTCU CX1 sports a state-of-the-art 66-channels SuperGPS receiver with unprecedented performance. Unique features  includes an advanced 3D-movement sensor and wireless RF transceiver.   The RTCU CX1 pro/pro-c product is a worthy member of a growing number of advanced telemetry/telematic products all based on the proven and powerful X32-architecture. The RTCU CX1 pro/pro-c is specifically based on the popular RTCU MX2i series and is 100% software compatible with all other X32 based devices from Logic IO. The unique features of the RTCU CX1 pro/pro-c includes a 3D-movement sensor supporting a range of new applications such as detailed driving behavior and even crash detection. The RTCU CX1 pro/pro-c has support for medium range wireless communication using the ISM 868 Mhz frequency band. This feature allows implementation of wireless I/O, RF-tracking and simple remote key fob applications.  There is on-board Li-Ion battery for uninterrupted operation during power-fail. The ISM RF antenna is on-board and internal to the device, and the unit is delivered pre-mounted with a 50 cm interface cable with power, I/O and RS232 or CAN bus signals easily accessible. For the most flexible installation the RTCU CX1 pro/pro-c is factory delivered with an external high-performance waterproof magnet GPS antenna and a small waterproof thumb-sized GSM antenna already installed. Everything necessary to install the device is therefore included in the box, so the total cost of the device deployment is effectively reduced to a minimum. The RTCU CX1 pro/pro-c is housed in a highly ruggedized IP66 waterproof encapsulation, which allows a new spectrum of applications to be realized due to the new installation possibilities. The RTCU CX1 pro/pro-c offers many other sophisticated features such as: Micro SD-CARD with up to 8 GB capacity and a 512 Kbyte internal flash drive with a FAT32 compatible file-system for easy sharing of files locally and remotely with a PC/Server.  The RTCU CX1 pro/pro-c is of course fully programmable using the user-friendly Integrated Development Environment (RTCU IDE) running under Windows. In this environment  the complete application is developed, simulated and finally transferred to the unit via a standard USB port or remotely by using GPRS or CSD (Datacall). The RTCU CX1 pro has RS232 interface with full Garmin FMI support, and the RTCU CX1 pro-c instead has a full CAN 2.0B interface. All other specifications are similar. The RTCU CX1 pro/pro-c feature-list includes:  100% software compatible with all current and past RTCU units!  Huge memory capacity with X32 Enhanced Memory support.   High performance 16g 3-axis accelerometer / movement sensor.  On-board medium range ISM 868 Mhz RF transceiver with antenna.  Support various for RF add-on modules.  Micro SD-CARD reader with FAT compatible file-system and up to 8 GB capacity.  Internal 512 KB Flash-Drive with full FAT support.  2 Digital inputs, 2 Digital high-side solid state outputs and 1 analog inputs.  RTCU CX1 pro: Standard RS232 port.  RTCU CX1 pro-c: Full CAN 2.0B controller with hardware filtering  Dedicated high-speed USB programming port.  Quad Band GSM support (850/900/1800/1900 Mhz)  GPRS Class 10 with full RTCU Gateway Professional support  Supports GSM features such as SMS/PDU/CSD/GPRS.  Full support for FTP and SMTP (email with attachment).  Ultra high-sensitivity low-power 66-channels SuperGPS receiver.  On-board high capacity Li-Ion battery (1000 mAh)  Temperature sensor  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Movement, Timeout, GSM-, CAN- or RS232-activity.   RTCU CX1 pro: Supports the Garmin Fleet Management / Navigation Interface  and the Mobile Data Terminal.  Pre-mounted with 50 cm interface cable with all signals easily available.  Pre-mounted with a standard small 'thumb' size GSM antenna and a very  compact magnet GPS antenna with 1.5 meter cable.  Compact ruggedized IP66 classified plastic encapsulation with mounting flange.  E1 automotive approval. ....many other advanced features Please read the Datasheet and Technical manual below Product datasheet V1.10 (pdf) RTCU CX1 pro technical manual V1.11 (pdf)    RTCU CX1 pro-c technical manual V1.11 (pdf)    Declaration of Conformity -- Ordering code: RT-CX1P   (RTCU CX1 pro)                   RT-CX1PC  (RTCU CX1 pro-c)
	RTCU CX1 flex   The RTCU CX1 flex is a compact and ruggedized telematic tracking and control platform based on the powerful X32-architecture. The RTCU CX1 flex offers a unique and outstanding approach allowing seamless upgrade with new hardware options – even after the product has been installed in the field! With a fully upgraded RTCU CX1 flex the functionality is approaching that of RTCU CX1 pro – merely lacking the RF transceiver and SD-CARD reader!   The RTCU CX1 flex is a low-cost product based on the RTCU CX1 pro/pro-c with a unique approach to the market. The standard hardware features of the RTCU CX1 flex are very powerful, but various hardware options can be specified when ordering or later deployed after unit installation. Options are easily activated using a short option key or barcode.   The following options are available:  I/O option:  Full I/O with 2 digital inputs, 2 digital outputs and 1 analog input.  RS232/FMI option: RS232 and full Garmin FMI support.  Performance option: Very fast execution (48 Mhz) and X32 Enhanced Memory. Options can be applied remotely to a unit already installed and in use by the customer. The RTCU CX1 flex is housed in a highly ruggedized IP66 waterproof encapsulation, which allows a new spectrum of applications to be realized. The RTCU CX1 flex feature list includes:  100% software compatible with all current and past RTCU units!  Huge memory capacity with optional X32 Enhanced Memory support.   Fast execution (24 Mhz) with optional very fast execution (48 Mhz).  High performance 16g 3-axis accelerometer / movement sensor.  Internal 512 KB Flash-drive with full FAT support.  Standard 1 Digital input, optional a total of  2 Digital inputs, 2 Digital high-side solid state outputs and 1 analog inputs.  Dedicated high-speed USB programming port.  Optional standard RS232 port.  Quad Band GSM support (850/900/1800/1900 Mhz)  GPRS Class 10 with full RTCU Gateway Professional support  Supports GSM features such as SMS/PDU/CSD/GPRS.  Full support for FTP and SMTP (email with attachment).  Ultra high-sensitivity low-power 66-channels SuperGPS receiver.  On-board Li-Ion battery (800 mAh)  Temperature sensor  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Movement, Timeout, GSM or RS232-activity.   Optional supports the Garmin Fleet Management / Navigation Interface  and the Mobile Data Terminal.  Pre-mounted with 50 cm interface cable with all signals easily available.  Pre-mounted with a standard small 'thumb' sized GSM antenna and a very  compact magnet GPS antenna with 1.5 meter cable.  Compact ruggedized plastic encapsulation with mounting flange.  E1 automotive approvals. ....many other advanced features. Please read the Datasheet and Technical manual below Product datasheet V1.10 (pdf) RTCU CX1 flex technical manual V1.01 (pdf) Declaration of Conformity -- Ordering code: RT-CX1F (RTCU CX1 flex) -- Options:       RT-O-CX1-IO  (I/O option)                   RT-O-CX1-RS  (RS232/FMI option)                   RT-O-CX1-PF  (Performance option)
	RTCU-MX2i pro/pro+ The RTCU MX2i pro/pro+ is the most powerful variants in the versatile MX2i family, and includes a list of advanced features only available on this State-of-the-Art product. The product is especially suited for mobile tracking applications with its on-board ultra high sensivity 66-channels SuperGPS-receiver and advanced power-management features. The unit is fully supported by the RTCU IDE development tool and is fully back-ward compatible with previous generation of RTCU units. The RTCU MX2i pro/pro+ is belonging to the "X32-Generation" of RTCU products based on a high performance industry leading ARM architecture. The RTCU MX2i pro/pro+ feature-list includes:  Up to 10 times faster execution than previous generation RTCU products  100% software compatible with all current and past RTCU units!  Huge memory capacity with X32 Enhanced Memory support   Standard SD-CARD reader with FAT compatible file-system for PC-compatibility  Internal 512 KB Flash-Drive with full FAT support  5 Digital inputs, 4 Digital high-side solid state outputs and 2 analog inputs  Full CAN 2.0B controller with hardware filtering  2 Serial ports. Optional RS485 support (shared with programming port)  Full MODBUS SLAVE support for SCADA integration or I/O slave module.  Full MODBUS MASTER support for easy I/O extension capability.  1-Wire bus for connecting devices such as ID-Button reader and  Temperature sensor  Quad Band GSM support (850/900/1800/1900 Mhz)  Voice/DTMF interaction support  Supports GSM features such as SMS/PDU/CSD/GPRS.  Full support for FTP and SMTP (email with attachment).  GPRS Class 10 with full RTCU Gateway Professional support  Ultra high-sensitivity low-power 66-channels SuperGPS receiver.  On-board high capacity Li-Ion battery (1900 mAh)  Vibration sensor with adjustable sensitivity  Temperature sensor  Piezo Buzzer for audible notification  Nokia compatible headset connector  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Vibration, Timeout, GSM-, CAN- or RS232-activity  Sleek aluminium design with black end-caps.  Highly expandable:  Bluetooth Smartantenna, VGA Camera module, Mobile Data Terminal  WiFi and Ethernet.  Supports the Garmin Fleet Management / Navigation Interface.  Optional Mounting Bracket Kit for easy "screw-on" installations  Alternative front end-cap with hidden SIM card reader.  MX2i pro+ adds 8 MByte of persistent memory for data-intensive applications  E1/e1 automotive approvals. The MX2i pro/pro+ offers a world-leading extremely high sensitivity SuperGPS 66-channels GPS receiver with unseen performance allowing precise positioning in the most difficult environments such as deep urban or even indoor-tracking! ....many other advanced features Please read the Datasheet and Technical manual below Product datasheet V2.10 (pdf) Technical manual V2.10 (pdf)    Declaration of Conformity -- Ordering code: RT-MX2IP (SuperGPS) -- Ordering code: RT-MX2IPP (SuperGPS and additional 8 MByte persistent memory)
	RTCU-MX2i eco+ The RTCU MX2i eco+ is the economical choice based on the full powered MX2i pro. Compared to the full powered MX2i pro the RTCU MX2i eco+ has a reduced feature set, but still maintains crucial core functionality such as a high-capacity battery, 1-wire support, full I/O capabilities and support for X32 enhanced memory for extremely huge programs. Fully supported by the RTCU IDE development tools and is of course fully backward compatible. The RTCU MX2i eco+ feature-list includes:  Up to 10 times faster execution than previous generation RTCU products  100% software compatible with all current and past RTCU units!  Huge memory capacity with X32 Enhanced Memory support  Internal 512 KB Flash-Drive with full FAT support  5 Digital inputs, 4 Digital high-side solid state outputs and 2 analog inputs   1 Serial port. Optional RS485 support (shared with programming port)  Full MODBUS SLAVE support for SCADA integration or I/O slave module.  Full MODBUS MASTER support for easy I/O extension capability.  1-Wire bus for connecting devices such as ID-Button reader and  Temperature sensor  Quad Band GSM support (850/900/1800/1900 Mhz)   GPRS Class 10 with full RTCU Gateway Professional support  Supports GSM features such as SMS/PDU/CSD/GPRS.  Full support for FTP and SMTP (email with attachment).  Ultra high-sensitivity low-power 66-channels SuperGPS receiver.   On-board high capacity Li-Ion battery (1900 mAh)  Vibration sensor with adjustable sensitivity  Temperature sensor    Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Vibration, Timeout, GSM-, or RS232-activity  Sleek aluminium design with black end-caps.  Expandable: Mobile Data Terminal  Optional Mounting Bracket Kit for easy "screw-on" installations   Alternative front end-cap with hidden SIM card reader.  Upgradeable to full Garmin Navigation support.  E1/e1 automotive approvals. The MX2i eco+ offers a world-leading extremely high sensitivity SuperGPS 66-channels GPS receiver with unseen performance allowing precise positioning in the most difficult environments such as deep urban or even indoor-tracking! ....many other advanced features Please read the Datasheet and Technical manual below Product datasheet V1.20 (pdf) Technical manual V1.10 (pdf)    Declaration of Conformity -- Ordering code: RT-MX2IEP (SuperGPS)
	RTCU-MX2 System On Module (SOM) The RTCU MX2 SOM (System On Module) with the core taken from the popular and powerful RTCU MX2i pro product. The MX2 SOM module can be designed into a customer application in the cases, where a standard product is not suitable. All signals are available on the SOM module for easy integration, and a powerful development board is offered for rapid development and integration… The MX2i SOM module will be available shortly, and a development kit will be offered. Additional information available on request. Please read the preliminary datasheet for additional information. Product datasheet V0.20 (pdf)
	RTCU-AX9 pro The RTCU AX9 pro is designed for a broad range of advanced wireless monitoring, control and remote access applications which require a product based on the most versatile and powerful platform available today. The RTCU AX9 pro shares the same powerful features as the other members of the X32-family with advanced features such as: ISM band RF communication, multiple RS485 ports with full MODBUS slave/master support, transparent support for MODBUS based I/O module extension and support for a M2M chip instead of a traditional SIM-card! The RTCU AX9 pro has been designed ground up for professional wireless industrial applications with its strong on-board I/O capabilities and multiple communication interfaces such as: 1-Wire, USB, RS232 and dual RS485 channels. In addition to full quad-band GSM for long-range wireless communication the RTCU AX9 pro integrates support for RF ISM for short range wireless communication. The on-board I/O system can be expanded almost indefinitely and completely transparent by adding external MODBUS compatible I/O modules! This unique I/O expansion capability, combined with the possibility to operate as a MODBUS master and slave simultaneously, positions the RTCU AX9 pro as the perfect product for SCADA-like applications. The RTCU AX9 pro offers many other sophisticated features such as: a 512 Kbyte internal flash drive and a Micro SD-CARD reader with a FAT32 compatible file-system for easy sharing of files locally and remotely. There is optional support for Bluetooth, Ethernet, Wi-Fi, Camera and a Mobile Data Terminal for user interaction. The RTCU AX9 pro is based on the well proven RTCU X32-architecture sharing powerful features such as: IVR (Interactive Voice Response) implementation using Voice/DTMF, SMS/PDU messages, optimized host implemented TCP/IP stack with full support for the Logic IO Gateway concept. Using the Logic IO VSMS (Virtual SMS) technology SMS, GPRS and CSD (Datacall) merge together, allowing any RTCU application, that uses the VSMS-messages paradigm, to transparently send / receive messages using either SMS, GPRS or CSD (Datacall) without any changes to the software already developed. The unit has full SMTP support for sending e-mails with attachments and file transfer with FTP for easy exchange of information with external sources. The RTCU AX9 pro is fully programmable using the user-friendly Integrated Development Environment (RTCU IDE) running under Windows. In the environment the complete application is developed, simulated and finally transferred to the unit via a standard USB port or remotely using GPRS or CSD (Datacall). The RTCU AX9 pro is also the logical successor to the former RTCU A9i product and for a brief description of the enhancements and transition please read the RTCU AX9 Series Product Information Bulletin. The RTCU AX9 pro feature-list includes:  Based on the well proven X32-architecture.  Huge memory capacity with X32 Enhanced Memory support.  100% software compatible with all current and past RTCU units!   Quad Band GSM Engine for world-wide operation.  On-board quad-band GSM antenna for cost and installation savings, or  SMA connector for external antenna.  Prepared for deployment of Gemalto embedded M2M SIM chip.  Supports all GSM features such as Voice/SMS/PDU/CSD/GPRS.  Medium range 868 Mhz ISM band RF tranceiver with on-board antenna.  Support various for RF add-on modules.  Full support for FTP and SMTP (email with attachment).  Interactive Voice Response System support (User defined messages/DTMF).  GPRS Class 10 with full RTCU Gateway Professional and VSMS support.  Standard Micro SD-CARD reader with FAT32 compatible file-system. Up to 2 GB!  Internal 512 KB Flash-Drive with full FAT32 support.  1-Wire bus for connecting devices such as ID-Button reader  and Temperature sensor.  Dedicated high-speed USB programming port.  RS232 port with optional RS485 support.  One RS232 port with all control signals available.  One dedicated RS485 for I/O extension or general purpose use.  Full MODBUS SLAVE support for SCADA integration or I/O slave module.  Full MODBUS MASTER support for easy I/O extension capability.  Transparent I/O extension, using I/O Manager integrated into the RTCU IDE.   Remote I/O appears the same way as on-board I/O!  On-board 5 Digital inputs and 4 relay outputs (5A @ 250VAC / 30VDC)  On-board 4 analog inputs and 4 analog outputs.  Up to four IEC62053-31 Class A (S0) compliant digital inputs.  Analog inputs supports 0..10V and 0..20 mA.  On-board temperature sensor.  On-board battery charger with high-capacity battery pack (1900 mAh).  Low temperature battery-charging down to -10 degrees Celsius.  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Timeout, GSM-, RS485- or RS232-activity  Wide AC/DC power range from 85..265 VAC / 8..36 VDC.  Encapsulated in an IP67 classified plastic box with PG cable glands.  Screw terminals for easy interfacing.  Highly expandable:  Bluetooth Smartantenna, VGA Camera module, Mobile Data Terminal  WiFi and Ethernet.  Internal expansion slot for possible future modules:  Zigbee, Ethernet, WiFi, Tetra, GPS, etc.  Fully supported by the powerful RTCU IDE development environment.  CE approval according to EU EMC Directive 2004/108/EU. ....many other advanced features Please read the Datasheet and Technical manual below Product datasheet V1.02 (pdf) Technical manual V1.05 (pdf)    Declaration of Conformity -- Ordering codes: RT-AX9P   (internal quad-band antenna) RT-AX9PX (SMA connector for external antenna )
	RTCU-AX9 eco The RTCU AX9 eco is a low-cost version based on the full-featured and powerful RTCU AX9 pro that still hosts a long list of advances features. Compared to the RTCU AX9 pro the RTCU AX9 eco differs on the following features:  No 868 Mhz ISM RF band transceiver.  No SD-CARD reader.  No secondary RS232 port.  No standard RS485 port.  No support for accessories such as Bluetooth, VGA Camera, Ethernet/WiFi.  No analog outputs and only 2 analog inputs.  No expansion slot.  Low-capacity battery.  No Enhanced X32 memory support.  The RTCU AX9 eco has been designed ground up for professional wireless industrial applications with its strong on-board I/O capabilities and multiple communication interfaces such as: 1-Wire, USB, RS232 and optional RS485. For world-wide operation the RTCU AX9 eco offers full quad-band GSM support with internal or external antenna. The RTCU AX9 eco offers many other sophisticated features such as: a 512 Kbyte internal flash drive with a FAT32 compatible file-system for easy sharing of files locally and remotely. There is optional support for a Mobile Data Terminal for advanced user interaction. The RTCU AX9 eco is based on the well proven RTCU X32-architecture sharing powerful features such as: IVR (Interactive Voice Response) implementation using Voice/DTMF, SMS/PDU messages, optimized host implemented TCP/IP stack with full support for the Logic IO Gateway concept. Using the Logic IO VSMS (Virtual SMS) technology SMS, GPRS and CSD (Datacall) merge together, allowing any RTCU application, that uses the VSMS-messages paradigm, to transparently send / receive messages using either SMS, GPRS or CSD (Datacall) without any changes to the software already developed. The unit has full SMTP support for sending e-mails with attachments and file transfer with FTP for easy exchange of information with external sources. The RTCU AX9 eco is fully programmable using the user-friendly Integrated Development Environment (RTCU IDE) running under Windows. In the environment the complete application is developed, simulated and finally transferred to the unit via a standard USB port or remotely using GPRS or CSD (Datacall). The RTCU AX9 eco is also the logical successor to the former RTCU A5i/A9i products. For a brief description of the enhancements and transition please read the RTCU AX9 Series Product Information Bulletin. The RTCU AX9 eco feature-list includes:  Based on the well proven X32-architecture.  100% software compatible with all current and past RTCU units!   Quad Band GSM Engine for world-wide operation.  On-board quad-band GSM antenna for cost and installation savings, or  SMA connector for external antenna.  Prepared for deployment of Gemalto embedded M2M SIM chip.  Supports all GSM features such as Voice/SMS/PDU/CSD/GPRS.  Full support for FTP and SMTP (email with attachment).  Interactive Voice Response System support (User defined messages/DTMF).  GPRS Class 10 with full RTCU Gateway Professional and VSMS support.   Internal 512 KB Flash-Drive with full FAT32 support.  1-Wire bus for connecting devices such as ID-Button reader  and Temperature sensor  Dedicated high-speed USB programming port.  RS232 port with optional RS485 support.   Transparent I/O extension, using I/O Manager integrated into the RTCU IDE.   Remote I/O appears the same way as on-board I/O (requires RS485)  On-board 5 Digital inputs and 4 relay outputs (5A @ 250VAC / 30VDC)  On-board 2 analog inputs.  Up to four IEC62053-31 Class A (S0) compliant digital inputs.  Analog inputs supports 0..10V and 0..20 mA.  On-board temperature sensor.  On-board battery charger with low-capacity battery pack (700 mAh).  Low temperature battery-charging down to -10 degrees Celsius.  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Timeout, GSM-, RS485- or RS232-activity  Wide AC/DC power range from 85..265 VAC / 8..36 VDC.  Encapsulated in an IP67 classified plastic box with PG cable glands.  Screw terminals for easy interfacing.  Expandable with the Mobile Data Terminal.  Fully supported by the powerful RTCU IDE development environment.  CE approval according to EU EMC Directive 2004/108/EU. ....many other advanced features Please read the Datasheet and Technical manual below Product datasheet V1.01 (pdf) Technical manual V1.03 (pdf)    Declaration of Conformity -- Ordering codes: RT-AX9E   (internal quad-band antenna) RT-AX9EX (SMA connector for external antenna )
	RTCU-DX4 pro The RTCU DX4 pro has been designed ground up for professional wireless industrial applications with its strong on-board I/O capabilities and multiple communication interfaces such as: CAN bus, 1-Wire, USB, RS232 and dual RS485 channels. The on-board I/O system can be expanded almost indefinitely and completely transparent by adding external MODBUS compatible I/O modules! This unique I/O expansion capability, combined with the possibility to operate as a MODBUS master and slave simultaneously, positions the RTCU DX4 pro as the perfect product for SCADA-like applications. The RTCU DX4 pro offers many other sophisticated features such as: A 512 KByte internal flash drive and a SD-CARD reader with a FAT32 compatible file-system for easy sharing of files locally and remotely with a PC/Server. There is optional support for Bluetooth, Ethernet, Wi-Fi, Camera module and a Mobile Data Terminal for user interaction. The RTCU DX4 pro is based on the well proven RTCU X32-architecture sharing powerful features such as: IVR (Interactive Voice Response) implementation using Voice/DTMF, SMS/PDU messages, optimized host implemented TCP/IP stack with full support for the Logic IO Gateway concept. Using the Logic IO VSMS (Virtual SMS) technology SMS, GPRS and CSD (Datacall) merge together, allowing any RTCU application, that uses the VSMS-messages paradigm, to transparently send / receive messages using either SMS, GPRS or CSD (Datacall) without any changes to the software already developed. The RTCU DX4 pro is of course fully programmable using the user-friendly Integrated Development Environment (RTCU IDE) running under Windows. In the environment the complete application is developed, simulated and finally transferred to the unit via a standard serial port or remotely using GPRS or CSD (Datacall). The impressive RTCU DX4 pro feature-list includes:  Based on the well proven X32-architecture.  Huge memory capacity with X32 Enhanced Memory support  100% software compatible with all current and past RTCU units!  Back-lit Graphical LCD display (144x32 pixels) with user defined character support.  Status panel showing battery/charger, GSM signal-strength and GPRS status.  Integrated fully programmable keyboard with 8 keys.  Quad Band GSM Engine for world-wide operation. External SMA connector.  Prepared for deployment of Gemalto embedded M2M SIM chip.  Supports all GSM features such as Voice/SMS/PDU/CSD/GPRS.  Full support for sending e-mails with attachment (SMTP)  Interactive Voice Response System support (User defined messages/DTMF).  GPRS Class 10 with full RTCU Gateway Professional and VSMS support.  Standard SD-CARD reader with FAT32 compatible file-system. Up to 2 GB!  Internal 512 KB Flash-Drive with full FAT32 support.  Full CAN 2.0B controller with hardware filtering.  1-Wire bus for connecting devices such as ID-Button reader  and Temperature sensor  USB ready (slave).  Programming port.  RS232 port with optional RS485 support (shared with programming port).  One RS232 port with all control signals available.  One dedicated RS485 for I/O extension or general purpose use.  Full MODBUS SLAVE support for SCADA integration or I/O slave module.  Full MODBUS MASTER support for easy I/O extension capability.  Transparent I/O extension using I/O Manager integrated into the RTCU IDE.   Remote I/O appears the same way as on-board I/O!  On board 8 Digital inputs, 8 digital outputs, 4 analog inputs and 4 analog outputs.  Up to four IEC62053-31 Class B (S0) compliant digital inputs.  Analog inputs supports 0..10V and 0..20 mA.  Two-part pluggable connectors for fast installation and maintenance.    On-board temperature sensor.  Piezo Buzzer for audible notification.  On-board battery charger with high-capacity battery pack (1900 mAh).  Low temperature battery-charging down to -10 degrees Celsius.  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Timeout, GSM-, CAN-, RS485- or RS232-activity  Encapsulated in a M36 DIN-rail enclosure.  Highly expandable:  Bluetooth Smartantenna, VGA Camera module, Mobile Data Terminal  WiFi and Ethernet.  Fully supported by the powerful RTCU IDE development environment.  CE approval according to EU EMC Directive 2004/108/EU. ....many other advanced features Please read the Datasheet and Technical manual below A complete range of MODBUS I/O modules are offered by Logic IO for easy connection to the RTCU DX4 pro product. Please see the MODBUS I/O Modules section. Product datasheet V1.11 (pdf) Technical manual V1.06 (pdf)    Declaration of Conformity -- Ordering code: RT-DX4P
	RTCU-DX4 eco The RTCU DX4 eco is designed for a broad range of advanced wireless monitoring, control and remote access applications which require a product based on the most versatile and powerful platform available on the market today. The RTCU DX4 eco is based on the powerful RTCU DX4 pro, but offers a reduced feature set to balance perfectly between low-cost and advanced features. The DX4 eco maintains the same I/O capabilities, including expandable I/O's, as the RTCU DX4 pro, and also offers support for a M2M chip solution instead of a traditional SIM-card! The DX4 eco has been designed ground up for professional wireless industrial applications with its strong on-board I/O capabilities and multiple communication interfaces such as:  1-Wire, RS232 and dual RS485 channels. The on-board I/O system can be expanded almost indefinitely and completely transparent by adding external Modbus compatible I/O modules! This unique I/O expansion capability, combined with the possibility to operate as a Modbus master and slave simultaneously, positions the RTCU DX4 eco as the perfect product for SCADA-like applications. The RTCU DX4 eco offers many other sophisticated features such as: A 512 Kbyte internal flash drive with a FAT32 compatible file-system for easy sharing of files locally and remotely with a PC/Server. The RTCU DX4 eco is based on the well proven RTCU X32-architecture sharing powerful features such as: SMS/PDU messages, optimized host implemented TCP/IP stack with full support the Logic IO Gateway concept. Using the Logic IO VSMS (Virtual SMS) technology SMS, GPRS and CSD (Datacall) merges together allowing any RTCU application, that uses the VSMS-messages paradigm, to transparently send / receive messages using either SMS, GPRS or CSD (Datacall) without any changes to the software already developed. The RTCU DX4 eco is of course fully programmable using the user-friendly Integrated Development Environment (RTCU IDE) running under Windows. In the environment the complete application is developed, simulated and finally transferred to the unit via a standard serial port or remotely using GPRS or CSD (Datacall). The impressive RTCU DX4 eco feature-list includes:  Based on the well proven X32-architecture  Huge memory capacity with X32 Enhanced Memory support  100% software compatible with all current and past RTCU units!  Quad Band GSM Engine for world-wide operation. External SMA connector.  Prepared for deployment of Gemalto embedded M2M SIM chip.  Supports GSM features such as SMS/PDU/CSD/GPRS.  Full support for sending e-mails with attachment (SMTP)  GPRS Class 10 with full RTCU Gateway Professional and VSMS support.  Internal 512 KB Flash-Drive with full FAT32 support.  1-Wire bus for connecting devices such as ID-Button reader  and Temperature sensor  Programming port.  One dedicated RS485 for I/O extension or general purpose use.  Optional RS485 support (shared with programming port).  Full MODBUS SLAVE support for SCADA integration or I/O slave module.  Full MODBUS MASTER support for easy I/O extension capability.  Transparent I/O extension using I/O Manager integrated into the RTCU IDE.   Remote I/O appears the same way as on-board I/O!  On board 8 Digital inputs, 8 digital outputs, 4 analog inputs and 4 analog outputs.  Up to four IEC62053-31 Class B (S0) compliant digital inputs.  Analog inputs supports 0..10V and 0..20 mA.  Two-part pluggable connectors for fast installation and maintenance.    On-board temperature sensor.  On-board battery charger with battery pack (700 mAh).  Advanced power-management with power-down and wait-for-event modes  Wake-up on: Digital input, Timeout, GSM-, RS485- or RS232-activity  Encapsulated in a M36 DIN-rail enclosure.   Fully supported by the powerful RTCU IDE development environment.  CE approval according to EU EMC Directive 2004/108/EU. ....many other advanced features Please read the Datasheet and Technical manual below A complete range of MODBUS I/O modules are offered by Logic IO for easy connection to the RTCU DX4 eco product. Please see the MODBUS I/O Modules section. Product datasheet V2.00 (pdf) Technical manual V2.01 (pdf)    Declaration of Conformity -- Ordering code: RT-DX4E

 

Starter kits / AVL Tester
	RTCU-MX2i pro GOLD Starter kit The RTCU-MX2i pro GOLD Starter kit includes everything required to start the evaluation of the RTCU-MX2i product. The Starter kit includes: The RTCU MX2i pro unit Combined "stick" GSM/GPS antenna Power cable with ignition ready for use (2 meter) Programming cable RJ45 to SUBD9 (male) RS232 converter Full range of TYCO connectors for interfacing to the unit FREE SANDISK 2GB SD-CARD Only a SIM-card and a Power-supply is required to start working with the starter kit! Order here! -- Ordering code: RT-MX2IPGOLD
	RTCU-MX2i pro FMI Starter kit The RTCU-MX2i pro FMI Starter kit includes everything listed in the GOLD starter kit above, but additionally includes:  Garmin Nüvi 1390 (Europe) Navigation device  Interface cable for connecting the RTCU MX2i pro with the Garmin device  Interface cable for connecting the Garmin device to the PC (Simulator) Please see more about the Garmin Fleet Management / Navigation interface here. This complete package includes everything to start-up the development of advanced Fleet Management, Messaging and Navigation applications! Order here! -- Ordering code: RT-MX2IPFMIKIT
	RTCU-AX9 pro Starter kit The RTCU AX9 pro Starter kit includes everything required to get started with the evaluation and test of the RTCU AX9 series. The Starter kit includes:  The RTCU AX9 pro unit with internal antenna.  USB Programming Cable  FREE SANDISK 2GB micro SD-CARD Only a SIM-card and power is required to start working with the starter kit! Order here! -- Ordering code: RT-AX9PKIT
	RTCU-DX4 pro GOLD Starter kit The RTCU-DX4 pro GOLD Starter kit includes everything required to get started with the evaluation and test of the RTCU DX4 series. The Starter kit includes:  The RTCU DX4 pro unit  GSM Antenna  Programming Cable  RJ45 to SUBD9 (male) RS-232 converter cable  FREE SANDISK 2GB SD-CARD Only a SIM-card and a Power-supply is required to start working with the starter kit! Order here! -- Ordering code: RT-DX4PGOLD
	Advanced AVL Tester for the MX2i and M11i Series. The AVL Tester represents a versatile instrument for all the professionals involved in the AVL business including software developers, service engineers and sales agents, because it offers the most realistic Control Unit (MX2 and M11 family) operating scenario - second only to the vehicle itself! Together with the RTCU IDE, it becomes a precious tool for the developer. The AVL Tester is a friendly user instrument adapted for the electrical repair shop for cars, where it can replace the RTCU-IDE platform. Delivered in a practical suit-case complete with power-supply and all necessary cables. Product datasheet V2.05 (pdf) -- Ordering code: RT-O-AVLTEST1

 

Software and Middleware
	RTCU IDE Programming Environment The RTCU IDE Programming Environment can be downloaded FREE here.
	RTCU Gateway Professional. The RTCU Gateway Professional is a middleware-solution that allows easy communication and access to remote units connected using TCP/IP communication technology. The product works in any Network architecture, without any need for expensive fixed IP-address or tunnelling solutions provided by the GSM operators. The RTCU Gateway Professional constitutes a back-bone in the communication between RTCU units and back-end/client applications. The product insures reliable and economical communication in any environment and application. The RTCU Gateway Professional also supports the advanced RTCU Upgrade & Deployment Server available as a Free add-on. Some of the features:  Advanced server architecture supports thousands of clients.  Runs as a Windows Service. This means that the Gateway service will start  without Windows logon and can also be remotely managed as a service.  Remote access via the included Windows GUI or via TELNET.  Full password protection for remote access.  Up to 10 client keys supported, for more flexible password management.  Disconnect timeout for inactive clients.  Advanced filtering feature allows monitoring/logging on specific client  and/or logging level.  Designed for several thousand clients and massive traffic.  Encrypted traffic for safer communication.  Compressed traffic. Reduces cost of communication.  Comes with a comprehensive user documentation.  Time service for centralized client time management (local/UTC).  Free for use up to 25 clients.  License must be purchased for additional clients. For more information, please also read the User and Installation Guide. RTCU Gateway - User and Installation Guide (pdf) -- Ordering code: RT-GGWPRO-<n>, available for free download (25 clients)
	RTCU Upgrade & Deployment Server. The RTCU Upgrade & Deployment Server (UDS) offers sophisticated features for Upgrade & Deployment of a, typically a larger, number of RTCU units in operation. The UDS can be configured by the user to insure that the specified units are running the correct firmware and application. The UDS will automatically upgrade the units as requested and this task will even take place during FULL unit operation. Any interruption in an upgrade attempt will be automatically handled and resumed to avoid any waste of expensive bandwidth. The following features are available:  Uses the RTCU Gateway Professional to establish a connection to remote units.  Runs as a Windows Service. This means that the UDS service will start without  Windows logon and can also be remotely managed as a service.  Remote access for monitoring/configuration via the included Windows GUI tool.  Upgrades firmware and application automatically according to user-configuration.  Firmware and application can be upgraded during full operation of the unit.  This unique feature minimizes downtime and the impact on the user.  Failed upgrade attempts will automatically be resumed at the point of interruption.  This unique feature will reduce the cost and time of upgrading.  Automatically or application driven decision when to switch over to the new  application/firmware. All that is required to switch over to the new  firmware/application is a reset of the unit, which will only interrupt the  operation for 10-20 seconds.  Up to 100 simultaneous upgrade sessions.  Support applications that use VPL upgrade notifications.  Support for automatic programming of un-programmed factory delivered unit.  Comprehensive logging and status features.  Comes with full user documentation. RTCU Upgrade and Deployment Server - User and Installation Guide (pdf) -- Ordering code: RT-GGWUPG, available for free download
	RTCU MICRO STANDARD APPLICATION The RTCU MICRO Standard application offers extremely easy setup/use of the unit for simple applications not requiring the full flexibility of the RTCU IDE programming environment. The pre-programmed functionality allows generating SMS-messages and/or calling up with user recorded voice message on the leading and/or falling edge of an input. By sending an user defined SMS-message or calling the unit using voice/DTMF the outputs can be controlled. Temperature monitoring and GPS functionality for geofencing are also included in the standard application. The configuration is performed either by sending SMS-messages to the unit or by using the RTCU Micro Configuration Tool available free of charge.   The RTCU MICRO STANDARD APPLICATION and the RTCU Micro Configuration Tool can be downloaded for free here.
	RTCU Citect SCADA driver Citect driver support for the complete line of RTCU Products has been developed by Vikingegaarden. For more information and ordering please contact www.vikingegaarden.com
Fleet Managment / Navigation
	Navigation and Messaging Platform (NMP) The Logic IO Navigation and Messaging Platform (NMP) is a powerful and extremely open platform for implementation of state-of the-art advanced fleet management applications integrating navigation, messaging, driver identification and job dispatch capabilities. The NMP platform works on almost any Microsoft Windows CE 6.0 based device and is based on the market leading Sygic navigation engine tightly integrated into the powerful RTCU concept. The NMP is fully backward compatible with already developed Garmin FMI based applications and includes full Garmin FMI functionality. Likewise, the full Mobile Data Terminal (MDT) API is fully supported opening up for a new level of customized user interaction. The key features of the Navigation and Messaging Platform:  Based on Sygic navigation engine under Microsoft Windows CE 6.0.  Versatile range of devices supported (large screens, ruggedized, etc).  Fully compatible with the Garmin FMI level 2 API.  Fully compatible with the Mobile Data Terminal API.  Single GPS source with data from the RTCU device.  Custom device logo and waypoints icons.  Customer language and unicode support.  Remote upgrade and configuration capabilities.  User written Windows CE applications can be deployed on the same device.  Open architecture allowing specialized functionality to be added. The NMP is currently supported by the RTCU MX2i pro/pro+ product from firmware version 2.62 and later. To connect the RTCU MX2i pro/pro+ device to the NMP device a special interface cable is required. It is also possible to connect the NMP device to the RTCU IDE Simulator allowing rapid development of complete fleet management and messaging applications within the RTCU IDE environment. For detailed information about the NMP interface please consult the RTCU IDE (V5.95 or later) on-line help or manual. Please contact Logic IO for additional information and device availability.
	Garmin Fleet Management / Navigation Interface The Garmin Fleet Management / Navigation API supports implementation of advanced fleet management applications integrating Navigation, Two-way messaging, Driver identification and Job dispatch capabilities. The Job dispatch functionality includes advanced features such as support for routes with multiple stops, route optimization and periodic Estimated Time of Arrival (ETA) notifications. The illustration below shows the system architecture with the various components constituting a complete Fleet Management Solution: The CX1 and MX2i series can be connected to certain navigation devices from Garmin allowing the development of highly advanced Fleet Management, Messaging and Navigation applications. The Garmin Navigation devices currently supported includes:  Garmin Dezl series  Garmin Nüvi 24xx series  Garmin Nüvi 22xx series  Garmin Nüvi 23xx series  Garmin Nüvi 12xx Series  Garmin Nüvi 13xx Series  Garmin Nüvi 14xx Series  Garmin Nüvi 465T (*)  Garmin Nüvi 7xx Series (*)  Garmin Nüvi 5000 Series (*) Older generation devices marked with (*) does not support level 2 of the navigation API, which includes the following functionality:  User authentication.  Up to three simultaneous users.  Waypoint support.  Message threading.  Delete message support.  Message formatting using HTML tags. To connect the RTCU CX1/MX2i series device to the Garmin Navigation device a special interface cable is required. It is also possible to connect the Garmin device to the RTCU IDE Simulator allowing development of complete Fleet Management applications within the RTCU IDE environment. The MX2i pro/pro+ and CX1 pro natively supports the Garmin Fleet Management interface, whether the CX1 flex and MX2i basic/eco+ does not. The MX2i basic/eco+ and CX1 flex can be upgraded to full Garmin Fleet Management functionality. For special applications the RTCU AX9 pro can also work with the Garmin Fleet Management interface. Logic IO is offering interface cables as well as Garmin Navigation devices constituting a complete solution. Currently we are offering the Garmin Dezl 560, Garmin Nüvi 1450 and Garmin Nüvi 1390. Also available is a complete MX2i FMI Starter kit with everything to get started on the development of applications For detailed information about the Garmin Fleet Management / Navigation API please consult the RTCU IDE (V5.10 or later) on-line help or manual. A large variety of interface cables are available with Free and Premium traffic services and with various connectors for MX2i (TYCO / RJ45), CX1 and finally the AX9 pro. Please see the ordering codes below. Product datasheet V1.31  (pdf) -- Ordering codes:    RT-O-GARMIN-FMI15    (CX1 / AX9)    RT-O-GARMIN-FMI45P   (CX1 / AX9. Premium traffic services)    RT-O-GARMIN-FMI15T   (MX2i series. TYCO6)    RT-O-GARMIN-FMI15R   (MX2i series. RJ45)    RT-O-GARMIN-FMI45PT  (MX2i series. TYCO6. Premium traffic services)    RT-O-GARMIN-FMI45PR  (MX2i series. RJ45. Premium traffic services)   RT-O-GARMIN-FMIPC    (PC Interface Cable. Requires also RJ45 FMI cable)   RT-O-GARMIN-UPG1     (MX2i basic/eco+ / AX9 upgrade for FMI support)
	Garmin Dezl 560L (Europe) Hit the open road with dezl 560L – the new Garmin navigator designed exclusively for the trucking industry. With large 5-inch display, rugged design, extra loud speaker and external video input for optional backup camera, dezl is ideally suited to the in-cab environment. Delivering advanced navigation, multi-route planning and calculation with nüRoute technology, dezl customises routes to your vehicle’s specific attributes, complete with trucking points of interest, truck speed limits, hazards and exits. With its 5-inch (12.7 cm) high-resolution touchscreen display, dezl 560L provides a wealth of information in great detail. PhotoReal Junction View delivers a realistic reproduction of road signs and junctions along your route, with stunning landscape detail for exceptional clarity right down to the exact trees and pylons! With Lane Assist, there’s no more guessing which lane you need to be in, dezl uses arrows to indicate the right lane for navigation at the right time – especially helpful when navigating complex motorway exits and junctions. So there’s no need for panic, hesitation or last-minute lane changes, even on unfamiliar routes. Preloaded with detailed full Europe maps (44 countries, truck coverage may vary), for turn-by-turn directions and spoken street names, dezl’s specialised routing supports truck-related restrictions customisable by your vehicle height, weight, length and hazardous materials. Simply enter your truck’s profile and dezl guides you onto suitable truck-verified roads, avoiding towns, cities and routes where relevant restrictions apply. You can even set up custom avoidances for specific roads and areas. Advanced multi-point truck routing finds the most efficient route between multiple stops and users can maintain various truck and driver profiles across a fleet, changing the active profile at any point. dezl makes finding an appropriate place to park much simpler with its “exit services” feature, which enables drivers to quickly search upcoming motorway exits for food, fuel, lodging, rest areas, truck stops and weigh stations. Once refuelled, the quick-release powered mount with Park Position Recall helps you navigate back to your parked vehicle to get quickly back on the road Whether your business acts globally or locally, the dezl 560L can be integrated into your existing or planned fleet management system. Garmin GPS solutions are a key part of today's most useful, versatile, and cost-efficient fleet monitoring solutions. Fully supports the Fleet Management / Navigation Interface level 2 advanced API. -- Ordering code: RT-GARMIN-DZ560
	Garmin Nüvi 1450 (Europe) The ultra-thin, 5-inch widescreen nüvi 1450 is a feature-packed navigator for Europe. It has Lane Assist and junction view for supreme route awareness. It includes  ecoRoute™ to calculate a more fuel-efficient route.  Key features: Only 16mm thin – ideal for use in and out of the car Lane Assist and junction view for help at upcoming junctions Public Transport and Pedestrian mode with optional cityXplorer download New optional AA City Guides for restaurant listings, attractions and more Garmin’s unique speed camera warnings Announces street names before you turn – e.g. “Turn right into Dell Road” Street level mapping for Europe. Fully supports the Fleet Management / Navigation Interface level 2 advanced API. -- Ordering code: RT-GARMIN-1450
	Garmin Nüvi 1390 (Europe) The ultra-thin, widescreen nüvi 1390 is a feature-packed navigator for Europe. It has Lane Assist and junction view for supreme route awareness. It includes Bluetooth® wireless technology for hands-free phone calls, ecoRoute™ to calculate a more fuel-efficient route.  Key features: Only 15mm thin – ideal for use in and out of the car Bluetooth wireless technology for handsfree calls Lane Assist and junction view for help at upcoming junctions Public Transport and Pedestrian mode with optional cityXplorer download New optional AA City Guides for restaurant listings, attractions and more Street level mapping for Europe, Garmin’s unique speed camera warnings Announces street names before you turn – e.g. “Turn right into Dell Road” Fully supports the Fleet Management / Navigation Interface level 2 advanced API. -- Ordering code: RT-GARMIN-1390
	Garmin Beanbag Friction Mount Keep your Nüvi in place with this portable friction mount. It’ll keep everything in plain sight when you need it and out of the way when you don’t. -- Ordering code: RT-GARMIN-10908-00
	Garmin Portable Friction Mount This new portable friction mount features a non-skid bottom and pliable base to keep the mount secure on your dashboard. The integrated arm can be folded down for easy storage in an automobile console or in luggage. Plus, the portable friction mounts sleek new design looks great on any dashboard!   -- Ordering code: RT-GARMIN-11280-00
	Garmin Dashboard Mount Click, swivel and go. Getting your Garmin unit ready to ride is easy with this compact dash mount. Adjusts easily, like a rearview mirror, so you can position your GPS for the best viewing angle. Secure mounting base to dash with either permanent or temporary adhesive disks (included). -- Ordering code: RT-GARMIN-10747-02
RF add-on modules
	RF add-on modules for the AX9 pro / CX1 pro Wireless connectivity is becoming a feature of choice for many applications, today. By using an off the-shelf embedded wireless module, the customer gets the benefit of using field proven RF hardware and protocol software to ensure the best performance possible. RF functionality of the RTCU units are designed to effortlessly interface with virtually any control, command, or monitoring applications for building automation systems, security systems, and industrial applications. The easy configurable network allows adapting to changing floor plans and requirements in a matter of minutes. New sensors and devices can be added to the network, as fast as they can be mounted. The highly sophisticated RF protocol implemented offers bi-directional communication with increased operational reliability and improves the basis for an extensive range of devices. Additionally the bidirectional communication ensures, that the tasks are received and accomplished correctly. Currently four main categories of add-on modules are supported: Remote control keyfobs: With remote control keyfobs the user defined functionality on the RTCU unit can be controlled. External relay modules: The relay modules provide relay outputs, which can be controlled remotely and are capable of switching external AC or DC powered loads. AC switching modules: The modules can be plugged directly into a wall receptacle and are capable of switching devices. Remote sensors: A variety of sensors can be connected to the RTCU unit remotely, which make them usable in wide variety of applications cost and time effectively. Currently the RF add-on modules are supported by the RTCU CX1 pro, RTCU CX1 pro-c and the RTCU AX9 pro/pro-x. Product datasheet v1.00 (pdf) Technical manual V1.00 (pdf) -- Ordering codes:    RT-O-HM-RC4B         (Handheld remote sender with 4 buttons. Black)
Accessories / Options
	MDT-200 Mobile Data Terminal The Mobile Data Terminal (MDT-200) extends the RTCU MX2i, RTCU DX4 pro and RTCU AX9 Series with a flexible and easy to use user-interface solution with many advanced features, allowing all kinds of two-way messaging applications to be implemented.  The Mobile Data Terminal is easily connected to the RTCU unit and includes the following features:  High contrast graphical Liquid Crystal Display (FSTN LCD).  White LED backlight with 10 step user selectable level.  320 x 240 pixels (1/4 VGA) resolution.  11 lines with 28 characters per line.  21 tactile keys and a 4 way cursor, all with LED backlighting.  Full numeric keypad for easy entry of numbers/text.  User defined characters for multilingual support.  Wide viewing angle.  Built in piezo buzzer.   UV stabilized, high temperature enclosure. Built for tough environments.  Flexible suction windscreen mount supplied.  Optional heavy duty PanaVise mounting bracket.  High-level VPL library.  Full simulator support in the RTCU-IDE.  MDT on/off and standby functionality for maximum power saving. Application development for the Mobile Data Terminal is easily archived with easy to use high-level library functions accessible from the RTCU IDE. The VPL application using the MDT can be fully simulated in the RTCU IDE environment before upload to a physical RTCU unit.   Product datasheet V1.01  (pdf)   Technical manual V1.01 (pdf) -- Ordering code: RT-O-MDT200-CX1 (with CX1 interface cable) -- Ordering code: RT-O-MDT200-MX2 (with MX2i/DX4 interface cable)                   -- Ordering code: RT-O-MDT200-AX9 (with AX9 interface cable)
	PanaVise mounting bracket for the MDT-200 Mobile Data Terminal The PanaVise 727-06 slimline mounting bracket for the MDT-200 Mobile Data Terminal is a heavy duty alternative to the standard windscreen suction mount, supplied as standard with the product. The PanaVise 727-06 is made of aluminium, zinc and steel and the overall mounting height (including shaft) is 152.4 mm (6 inch). Flexible movement with 210° Tilt, 360° Turn & 360° Rotation at both ends. -- Ordering code: RT-O-MDT-727-06
	Bluetooth Smart-antenna for the RTCU MX2i pro / DX4 pro / AX9 pro The Bluetooth Smart-antenna is an exciting accessory for the RTCU MX2i pro / RTCU DX4 pro / RTCU AX9 pro. It allows a wide group of applications to be implemented. The Bluetooth Smarta-ntenna supports the Serial Port Profile (SPP) and Hands-free Profile Audio Gateway (HFP-AG). These profiles supports connection to a wide range of devices, such as: PDA, Printer, Barcode reader, RFID reader, headset and hands-free speakerphone. The Bluetooth Smart-antenna is easy-to-use through the dedicated functions in the RTCU IDE development software. The Bluetooth Smart-antenna hands-free profile is fully compatible with the Garmin Bluetooth hands-free feature! The Bluetooth Smart-antenna are available in three versions for the RTCU MX2i pro, RTCU DX4 pro and the RTCU AX9 pro.   Product datasheet V1.03  (pdf)   Technical manual V1.05 (pdf) -- Ordering code: RT-O-BT1-MX2 (With audio connector for the RTCU MX2i pro) -- Ordering code: RT-O-BT1-DX4 (Without audio primarily for the RTCU DX4 pro) -- Ordering code: RT-O-BT1-AX9 (Without audio primarily for the RTCU AX9 pro)
	WLAN / Ethernet add-on module for the RTCU MX2i pro / DX4 pro / AX9 pro The WLAN-100 / ETH-100 add-on module allows connection to the RTCU Gateway Professional or to any TCP/IP socket enabled device through either a standard LAN or through an increasing number of Wi-Fi hot-spots globally available. Using (W)LAN in many cases means that large amount of data can be transferred for FREE or at a very low cost. The WLAN-100 / ETH-100 supplement GPRS and both communication methods can be used selectable under full control of the VPL application. The WLAN-100 supports connection to a standard Wi-Fi access point and is supplied with the necessary interface cable for the MX2i pro/DX4 pro or AX9 pro and a SMA antenna. The ETH-100 supports connection to a standard Ethernet 10/100 Mbps cable infrastructure and is supplied with the necessary interface cable for the MX2i pro / DX4 pro or AX9 pro and a RJ45 patch cable. Advanced configuration is supported using an easy to use web-based interface, where various parameters such as DHCP / IP-address, net-mask and security parameters are configured. Supports security using WEP, WPA and WPA2. Product datasheet V2.03  (pdf)   Technical manual V2.13 (pdf) -- Ordering code: RT-O-ETH100-MX2 (Ethernet) -- Ordering code: RT-O-WLAN100-MX2 (Wi-Fi) -- Ordering code: RT-O-ETH100-AX9 (Ethernet) -- Ordering code: RT-O-WLAN100-AX9 (Wi-Fi)
	VGA Camera Module for the RTCU MX2i pro / DX4 pro / AX9 pro The VGA Camera Module for the RTCU MX2i pro, RTCU DX4 pro and RTCU AX9 pro is extending the functionality of this powerful platform with the capability to take colour pictures in standard JPEG format. The pictures taken can be transmitted over GPRS to a server and/or saved to an SD-CARD file. The Camera Module is supporting implementation of applications such as:  Remote monitoring of equipment, devices, work areas and locations  Vehicle, including driver/passenger, monitoring  Security applications  Any event-trigger applications  Stealth security applications  ....many other applications where "a picture is worth a thousand words"... The VGA Camera module connects directly to the RTCU unit and requires no external power-supply. Delivered with 3 meter cable. The VGA Camera module is easy-to-use through the dedicated functions in the RTCU IDE development software. Note: This is an enhanced product based on the CAM-100. The quality, performance and lens have been improved. Software compatibility is maintained. Product datasheet V1.00  (pdf)   Technical manual V1.00 (pdf) -- Ordering code: RT-O-CAM120-MX2 (For MX2 pro and DX4 pro) -- Ordering code: RT-O-CAM120-AX9 (For AX9 pro)
	Enfora SA-G+ GSM/GPRS Modem The Enfora SA-G+ modem is a certified quad-band integrated platform, that enables simple integration through a standard RS232 serial connection. Small compact modem with functions such as GPRS, data calls (CSD), speech and SMS. External SIM-card holder w. lock. Supply for 6-40VDC. With this modem it is possible to establish a CSD (data dial-up) connection the the RTCU products in the case where a GPRS connection can not be established.   GSM1308 Enfora SA-G+ Users Guide V1.03 (pdf) GSM1308 Enfora SA-G+ AT Command Set V1.01 (pdf) -- Ordering code: RT-O-GSMMOD1
	Mounting bracket for the RTCU MX2i Series The Mounting bracket is used in the cases were screw-hole mounting is required for the RTCU MX2i Series. Installation is very easy as the bracket is designed to simply fit on the MX2i Series without need for any tools. The rubber gasket between the bracket and the MX2i Series insures that when the bracket is fastened with the two screw-holes onto the surface it will remain in place. Product datasheet V2.00  (pdf) -- Ordering code: RT-O-MX2BRI (For the complete MX2i Series)
	MX2i Series front end-cap with hidden SIM card reader In the MX2i Series the SIM card is by standard easily accessible from the outside, which is a huge advantage in most applications. For special requirements an alternative front end-cap with the SIM card reader hidden behind the front end-cap can be delivered. Using this front-end cap it is therefore necessary to unscrew the front end-cap to gain access to the SIM card. The installation is easy by a simply exchange of the standard front end-cap supplied with any MX2i Series unit -- Ordering code: MX2ECO-FRONT-SIM (For MX2i eco+) -- Ordering code: MX2PRO-FRONT-SIM (For MX2i pro / pro+)
	TYCO Mate'N'Lock Connector accessories  for the RTCU MX2i Series The RTCU MX2i Series uses the TYCO Mate'N'Lock connector type for most of its external interfacing (please see the RTCU MX2i product for details). The following TYCO Mate'N'Lock are available for the RTCU MX2i Series:    4 pins Connector house for the Power-connector -- Ordering code: RT-O-TYCO-H4 (10 pcs)  6 pins Connector house for the Serial port 1-connector -- Ordering code: RT-O-TYCO-H6 (10 pcs)  12 pins Connector house for the Communication-connector -- Ordering code: RT-O-TYCO-H12 (10 pcs)  16 pins Connector house for the I/O-connector -- Ordering code: RT-O-TYCO-H16 (10 pcs)  Crimp contacts -- Ordering code: RT-O-TYCO-CR (100 pcs)  Original TYCO Crimp hand tool for fast&easy crimp assembly  Safe, fast and easy crimp cable assembly.  -- Ordering code: RT-O-TYCO-TOOL Tyco Crimp Hand Tool Guide V2.00 (Logic IO) (pdf) Original documents from Tyco: Tyco Mate'N'Lock Application Specification  114-13000 (TYCO) (pdf) Tyco Crimp Hand Tool - Instruction Sheet 408-8547 (TYCO) (pdf)
	Sandisk SD-CARD approved for use with the RTCU MX2i  / DX4 Series The RTCU MX2i and DX4 Series can access an industry standard SD-CARD memory card using the FAT16/FAT32 file-system for full Microsoft Windows file sharing compatibility. For capacities larger than 2 GByte (SDHC) a Sandisk Micro SD-CARD is required. -- Ordering code: RT-O-SDC2G (Sandisk 2 GByte SD-CARD)
	Sandisk Micro SD-CARD approved for use with the RTCU AX9 pro / CX1 pro. The RTCU AX9 pro and RTCU CX1 pro/pro-c can access an industry standard Micro SD-CARD memory card using the FAT16/FAT32 file-system for full Microsoft Windows file sharing compatibility. For capacities larger than 2 GByte (SDHC) a Sandisk Micro SD-CARD is required. -- Ordering code: RT-O-SDCM2G (2 GByte Micro SD-CARD)
	USB 2.0 SD-CARD / Micro SD-CARD card reader A compact USB 2.0 card-reader that can read both SD-CARD and Micro SD-CARD without any additional adaptors. Transparent grey with protective lids. -- Ordering code: RT-O-SDRD1
	DIN Rail Power Supply, 24 volt / 2.5A. DIN rail mounted power supply especially suited for use with the RTCU DX4 series. Features:  Universal AC input for world-wide use.  Protections: Short circuit / overload / over voltage.  Cooling by free air convection.  LED indicator for power on.  DC OK relay contact.  24 Volt / 2.5 A.   Product datasheet (pdf) -- Ordering code: RT-O-MDR6024
	RTCU AX9 Series / A9i / A5i Wall Mount Kit The RTCU AX9 Series Wall Mount Kit includes 4 corner mounting brackets for easy wall mounting of the unit. -- Ordering code: RT-O-AX-WM1
	RTCU A9i / A5i Internal Battery Backup Package The RTCU A9i /A5i Internal Battery Backup package for the RTCU A9i and RTCU A5i offers uninterruptible operation even when a power failure of the external power supply occurs. The Backup Battery module is easy installable and has a capacity of 700 mAh @ 12 Volt. The firmware includes functionality to get the current voltage of the Battery Backup Package and to start/stop the charging. Product datasheet V1.00 (pdf) -- Ordering code: RT-O-AX-BAT (700 mAh)
MODBUS I/O Expansion Modules
	RT-EX-9017:  8 Analog Inputs, 16 Bit To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9017 module offers 8 Analog Inputs with a resolution of 16 bits. Several Voltage and Current configurations are available, including: +/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V and +/-20 mA. Product datasheet V1.02  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9017
	RT-EX-9036:  6 Analog RTD Sensor Inputs. 16 Bit To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9036 module offers 6 Analog RTD Inputs with a resolution of 16 bits. PT-100 sensors in various configuration is supported with a high resolution of 16 Bit. Product datasheet V1.02  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9036
	RT-EX-9024:  4 Analog Outputs, 14 Bit. To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9024 module offers 4 Analog Outputs with a resolution of 14 bits. Several Voltage and Current configurations are available, including: +/-10 V, 0..10 V, +/-5 V, 0..5 V, 0..20 mA and 4..20 mA. Product datasheet V1.01  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9024
	RT-EX-9041D:  14 Digital Inputs (isolated) To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9041D module offers 14 isolated Digital Inputs and LED indication of the inputs status. Product datasheet V1.01  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9041D
	RT-EX-9043D:  15 Digital Outputs To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9043D module offers 15 Digital Outputs and LED indication of the outputs status. Product datasheet V1.01  (pdf)   Technical manual V2.01 (pdf) -- Ordering code: RT-EX-9043D
	RT-EX-9044D:  4 Digital Inputs and 8 Digital Outputs (isolated) To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9044D module offers 4 isolated Digital Inputs and 8 isolated Digital Outputs. LED indication is available for Input/Output status. Product datasheet V1.01  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9044D
	RT-EX-9065D:  4 Digital Inputs and 5 Digital Relay Outputs To expand the I/O capability of certain RTCU products an MODBUS compatible I/O module can be connected to the product and configured using the I/O Expansion configuration functionality available in the RTCU IDE. The I/O Expansion is completely transparent to the application and remote I/O are therefore accessed and used exactly as on-board I/O. Logic IO are offering a range of MODBUS I/O modules that are high-quality, low-cost and extremely easy to set-up and use due to the set-up utility included in the RTCU IDE. The EX9065D module offers 4 isolated Digital Inputs and 5 high-power Digital Relay Outputs (5A/230V). LED indication is available for Input and Output status. Product datasheet V1.01  (pdf)   Technical manual V2.00 (pdf) -- Ordering code: RT-EX-9065D
Modular 1-Wire
	Modular 1-Wire concept The modular 1-Wire concept is offering high flexibility and customization for a wide range of applications utilizing multiple 1-Wire devices. The 1-Wire concept is based on building blocks such as combiners, splitters and unit interface cables connected together with standard and widely available RJ45 UTP cable technology. Unit interface cables are available which connect the RTCU unit to a splitter or combiner, that again connects to branches with more splitters and combiners and at the end-points of this arbitrary topology various lengths of 1-Wire devices such temperature sensors or ID-button readers can be connected. As the backbone is based on standard RJ45 UTP cable technology expanding a network can easily be achieved. Product datasheet v1.00 (pdf) Technical manual V1.00 (pdf)
	Modular 1-Wire unit interface cable The modular 1-Wire interface cable makes the physical bridge to the modular 1-Wire network. The modular network can easily be customized with the use of standard RJ-45 splitters and combiners to achieve the needed 1-Wire network. Multiple 1-Wire devices such as temperature sensors and ID-Button readers can be connected to one RTCU unit. The modular 1-Wire interface cables are available for the MX2i series and for the DX4/AX9 series. The modular 1-Wire interface are delivered with a RJ-45 connector for easy connection to a combiner if only a single 1-Wire device is connected. For multiple 1-Wire devices a splitter can be used. No external power supply is required as the 1-Wire devices derives power directly from the 1-Wire bus simplifying installation. Please refer to the Modular 1-Wire Technical manual for installation and use. Product datasheet v1.00 (pdf) -- Ordering codes:    RT-O-1WM-IF1         (Unit interface cable for AX9/DX4)   RT-O-1WM-IF2         (Unit interface cable for MX2i)
	Modular 1-Wire splitter, combiner and RJ45 UTP cables The modular 1-Wire concept is build on standard RJ45 cable technology and by using splitters, combiners and RJ45 UTP cables any network topology required by the application can be designed and implemented. The following parts are offered:  RJ45 combiner. Combines two RJ45 cables  RJ45 splitter. Splits one RJ45 cable into two cables.  RJ45 UTP cables. HQ cables in various lengths. -- Ordering codes:    RJ45-CMB             (RJ45 combiner)    RJ45-SPL2            (RJ45 2-way splitter)    RJ45-UTP03M          (RJ45 HQ UTP cable -  3 meter)    RJ45-UTP05M          (RJ45 HQ UTP cable -  5 meter)    RJ45-UTP07M          (RJ45 HQ UTP cable -  7 meter)    RJ45-UTP10M          (RJ45 HQ UTP cable - 10 meter)    RJ45-UTP15M          (RJ45 HQ UTP cable - 15 meter)
	Modular 1-Wire temperature sensor The modular 1-Wire temperature sensor are delivered with a RJ-45 connector for easy connection to the modular 1-Wire network via a combiner or splitter allowing easy installation in any application. The temperature sensor offers an accuracy of typical +/- 0.5ºC and ranges from –55ºC to +125ºC. The communication between the RTCU unit and the temperature sensor is done through the 1-Wire interface, requiring only a single wire and a ground to establish the data connection. No external power supply is needed as the temperature sensor derives power directly from the 1-wire bus simplifying application set-up. From the RTCU application temperatures are measured with a simple function similar to the known board temperature function. The temperature sensor has a unique factory-lasered 64-bit serial number allowing connection of multiple temperature sensors on the same 1-Wire bus. Please consult the RTCU IDE on-line help for more information about the supported 1-Wire Temperature Sensor functions. The Modular 1-Wire temperature sensor can be delivered in two length; 3 or 10 meters of cable with a RJ-45 for easy installation into the modular 1-Wire network. If another length is required the modular 1-Wire network is easy expandable with a combiner or splitter and standard UTP network cable. Product datasheet v1.00 (pdf) -- Ordering codes:    RT-O-1WM-TEMP3       (Modular 1-Wire temperature cable -  3 meter)    RT-O-1WM-TEMP10      (Modular 1-Wire temperature cable - 10 meter)
	Modular 1-Wire ID-Button reader The modular 1-wire ID-Button reader features an easy to install and easy to use 1-Wire ID-Button reader with controllable LED indicator.  The modular 1-Wire ID-Button reader are delivered with a RJ-45 connector for easy connection to the modular 1-Wire network via a combiner or splitter allowing easy installation in any application. The ID-Button reader offers a way to uniquely identify persons or items equipped with ID-buttons. The communication between the RTCU unit and the ID-Button reader is done through the 1-Wire interface, requiring a single data wire, a ground to establish the data connection, an extra wire is dedicated for controlling the LED present in the ID-Button reader. No external power supply is needed as the ID-Button reader derives power directly from the 1-wire bus simplifying application set-up. From the RTCU application reading an ID-Button and controlling the LED indicator is easily done with function call. IDButtons with on-board non-volatile memory is also available for storing data directly in the ID-Button. Please consult the RTCU IDE on-line help for more information about the supported 1-Wire ID-Button Reader functions. The modular 1-Wire ID-Button reader can be delivered in two length; 3 or 10 meters of cable with a RJ-45 for easy installation into the modular 1-Wire network. If another length is required the modular 1-Wire network is easy expandable with a combiner or splitter and a standard network cable. Product datasheet v1.00 (pdf) -- Ordering codes:    RT-O-1WM-IDRD3       (Modular 1-Wire ID-Button reader -   3 meter)    RT-O-1WM-IDRD10      (Modular 1-Wire ID-Button reader -  10 meter)
1-Wire accessories
	iButton - ID Button for user identification This ID Button can be read by an iButton reader connected to a suitable RTCU unit for easy and secure identification of a person/item identified with a unique ID button. This can be used for numerous applications: driver identification, turning alarm on/off, usage registration etc. -- Ordering code: RT-O-1W-ID1X (10 pcs.)
	iButton - ID Button Fobs This ID Button Fob holds the ID Button in place so that it is convenient available whenever needed. Available in black colour. -- Ordering code: RT-O-1W-FOB1X (black) (10 pcs.)
	iButton - ID Button for user identification with on-board memory This ID Button can be read and written to by an iButton reader connected to a suitable RTCU unit for easy and secure identification of a person/item identified with a unique ID button. The on-board non-volatile memory of 116 bytes of data opens up a broad range of new applications, where the user specific information can be stored directly into the iButton itself. Applications include access control, work-in-progress tracking, electronic travelers, storage of calibration constants and debit tokens. -- Ordering code: RT-O-1W-ID2
	iButton - ID Button Reader This ID Button Reader is used for reading the ID Button above. It is supported in the hardware and firmware of the RTCU MX2i pro/eco+ and the RTCU AX9/DX4 series products. Comes with 3 meter cable and includes a LED that can be controlled from software. Can easily be mounted on the dashboard of a vehicle. Also see the modular 1-wire section. Technical manual V1.12 (pdf) -- Ordering code: RT-O-1W-IDRD2 (AX9/DX4) -- Ordering code: RT-O-1W-IDRD3 (MX2i pro/eco+)
	External Temperature sensor This 1-Wire based external temperature sensor can measure temperatures from -55 to 125 degrees Celsius with a precision of 0.5 degrees Celsius. It is supported in the hardware and firmware of the RTCU MX2i pro/eco+ and the RTCU AX9/DX4 series products. Comes standard with 3 meter cable and a waterproof temperature-sensor. Also see the modular 1-wire section. Product datasheet v1.02 (pdf) Technical manual V1.12 (pdf) -- Ordering code: RT-O-1W-TEMP2 (AX9/DX4/A9i) -- Ordering code: RT-O-1W-TEMP3 (MX2i pro/eco+)
Power and I/O Cables
	Power cable with ignition for the RTCU MX2i Series Power cable with ignition for the RTCU MX2i Series. With separate wires: red=Plus, black=Minus and green=Ignition. Length: 2 meter. -- Ordering code: RT-O-PWR-MX2
	I/O cable for the RTCU MX2i Series High quality I/O cable for the MX2i Series with wiring for Digital Input, Digital Output and Analog Inputs. Length: 1.3 meter. I/O cable wiring diagram (PDF) -- Ordering code: RT-O-16P-MX2
	Option: RS485 The RS485 option can be specified when ordering the RTCU A9i, RTCU D4, RTCU MX2i pro/eco+ and the RTCU DX4 pro. -- Ordering code: RT-O-RS485
Programming Cables / Adaptors
	RTCU Programming Cable for the RTCU MX2i and DX4 Series This programming cable is used for communicating with the a RTCU MX2i and DX4 series units from programs such as the RTCU IDE. -- Ordering code: RT-O-PCA-MX2
	RTCU Programming Cable for the RTCU AX9 Series High-Quality USB programming cable with two mounted Ferrite cores for communicating with the RTCU AX9 Series from programs such as the RTCU IDE. -- Ordering code: RT-O-PCA-USB1
	RTCU Programming Cable for the RTCU CX1 Series High-Quality USB programming cable with two mounted Ferrite cores for communicating with the RTCU CX1 Series from programs such as the RTCU IDE. -- Ordering code: RT-O-PCA-USB2
	RS232 RJ45 to SUB-D9 (male) cable for the RTCU MX2i pro / DX4 Pro This cable is for converting the RJ45 Serial port to a standard SUB-D9 (male) connector. Cable length: 20 cm. -- Ordering code: RT-O-RJ45SM
	Barcode reader for RTCU CX1 flex option activation and serial# scanning This handy barcode reader can be used to easily activate RTCU CX1 options, but works equally well for scanning the serial-number label present on all RTCU units. Connects to a standard USB port and emulates a standard keyboard interface. -- Ordering code: RT-O-BAR-RD1
	PC-CARD RS232 Adaptor for Laptop The PC-CARD RS232 Adaptor is used to extend any portable PC with a standard RS232 port required for communication with the RTCU Products. 1 x RS232 9-pin connector. 32-Bit Cardbus type II. Drivers for Windows 2000/XP/Server-2003/Vista, Linux Kernel 2.6 or later. -- Ordering code: RT-O-PC-SER3
	USB <-> RS232 Adaptor USB<->RS232 adaptor that allows reliable communication with RTCU units using RS232 as the programming interface. This adaptor requires no external power and has a high performance due to its enhanced 128 bytes transmit and massive 384 bytes receive FIFO's. Two LED indicators for RX/RX status monitoring. Installs as a standard and user-selectable COM port. 1 x RS232 9-pin connector. Cable length 25 cm Drivers for Windows 2000/XP/Server-2003/Vista and Windows 7. -- Ordering code: RT-O-PC-SER3
GSM / GPS Antennas
	RTCU GSM Angled Dual-band whip antenna This small GSM dual band antenna with SMA male connector can be mounted directly onto the RTCU unit. The antenna has a adjustable angled connector. Product datasheet (pdf) -- Ordering code: RT-O-GSM-S1
	RTCU GSM quad-band Window antenna - WIN3 This is a compact quad-band window GSM antenna with SMA male connector and 3 m. cable.   Product datasheet (pdf) -- Ordering code: RT-O-GSM-WIN3
	RTCU GSM dual-band whip antenna This small GSM dual band antenna with a SMA male connector can be mounted directly onto the RTCU unit. Length 185 mm. Product datasheet (pdf) -- Ordering code: RT-O-GSM-WHIP2
	RTCU GSM dual-band DOTCOM antenna This is a round and small GSM antenna, only ø33 x 7 mm. Very easy to hide with a SMA male connector and 2,5 meter cable.   Product datasheet (pdf) -- Ordering code: RT-O-GSM-DOT
	RTCU GPS Active Antenna with magnet. This compact GPS antenna with a SMB female connector and 3 meter cable is waterproof and includes a powerful magnet for easy installation. Can be connected directly to the MX2i series. Product datasheet (pdf) -- Ordering code: RT-GPSANT3
	RTCU "round" GPS Active Antenna This is a round and small GPS antenna, only ø39 x 13 mm. Very easy to hide. Comes with a SMB female connector and 2,5 meter cable. Can be connected directly to the MX2i series. Product datasheet (pdf) -- Ordering code: RT-O-GPSANT2
	RTCU quad-band GSM/GPS Antenna This is a low-cost combined quad-band GSM/GPS antenna for easy installation. The slim form-factor of this antenna makes it ideal for installation in difficult places. The dimensions are only: 96mm x 36mm x 15mm. It has a SMB female connector for the GPS and a SMA male connector for the GSM part. Comes with 3 or 5 meter cable and can be connected directly to the MX2i series. Must be mounted with the adhesive side facing reverse the sky - towards the installation surface. Our most popular antenna! Product datasheet (pdf) -- Ordering codes:     RT-O-GPSGSM-X1   (3 meter cable)     RT-O-GPSGSM-X1L  (5 meter cable)
	RTCU combined "round" quad-band GSM/GPS Antenna This is a low-cost combined quad-band GSM/GPS antenna for easy installation. It has a SMB female connector for the GPS and a SMA male connector for the GSM part. ø70 × 15 mm. Comes with 3 meter cable and can be connected directly to the MX2i series. Must be mounted with the adhesive side facing the sky. Product datasheet (pdf) -- Ordering code: RT-O-GPSGSM4
	RTCU compact quad-band roof GSM/GPS Antenna This is a compact low-cost high-quality quad-band roof GSM/GPS antenna for easy outdoor installation - typically on roof-top of vehicles. It has a SMB female connector for the GPS and a SMA male connector for the GSM part. Comes with 5 meter cable and can be connected directly to the MX2i series. Product datasheet (pdf) -- Ordering code: RT-O-GPSGSM-X3
	RTCU quad-band GSM/GPS antenna for the CX1 series. Combined quad-band GSM/GPS antenna for the CX1 series offered as an alternative to the standard supplied antennas. The slim form-factor of this antenna makes it ideal for installation in difficult places. The dimensions are only: 96mm x 36mm x 15mm. It has a SMA female connector for both GPS and GSM connection and comes with 3 meter cable for directly connection to the CX1 series. Must be mounted with the adhesive side facing reverse the sky - towards the installation surface. Product datasheet (pdf) -- Ordering code: RT-O-GPSGSM-SS1
Obsolete Products